選擇Create Failover Group:

a. 選擇該頁面中的Link Aggregate Instance, 例如901。

b. 選擇Failover Policy， 用缺省的即可。

c. 選擇要做成failover group的網口，這張圖上是lan2,lan3,lan10.

d. 輸入Priority,如lan2 –>2, lan3->4,lan10->4等。(如果Failover Policy 為cost based,則可能需要輸入cost)

e. 選擇Advanced Parameters，缺省即可，如真有需要，可以更改。

f. 選擇Configuration Options。根據自己需要選擇。

g. OK，創建failover group.

配置文件保存在：/etc/rc.config.d/hp_apaconf, /etc/rc.config.d/hp_apaportconf, 和 /etc/lanmon/lanconfig.ascii 當中.

查看/etc/rc.config.d/hp_apaportconf應該可以看到這兩個網卡的priority是不一樣的。

最后，通過命令重新啟動APA或是直接啟動主機即可:

# /sbin/init.d/hplm stop

# /sbin/init.d/hpapa stop

# /sbin/init.d/hpapa start

# /sbin/init.d/hplm start

其中l(wèi)an2 ,lan3綁定成lan901, lan4,lan5綁定成lan902.

lan901的地址配置成

IP_ADDRESS[1]=”10.0.25.193″

SUBNET_MASK[1]=”255.255.255.192″

lan902的地址配置成：

IP_ADDRESS[2]=”192.168.100.1″

SUBNET_MASK[2]=”255.255.255.0″

通過命令nwmgr可以顯示一個正常的lan901的狀態如下：

db1@[/#]nwmgr -S apa -I 901 -v

lan901 current values:

Speed = 1 Gbps Full Duplex

MTU = 1500

Virtual Maximum Transmission Unit = 0

MAC Address = 0x00237d3e33ec

Network Management ID = 9

Features = Linkagg Interface

IPV4 Recv CKO

IPV4 Send CKO

VLAN Support

VLAN Tag Offload

64Bit MIB Support

Load Distribution Algorithm = LB_HS

Mode = LAN_MONITOR

Parent PPA = –

APA State = Up

Membership = 3,2

Active Port(s) = 3

Ready Port(s) = 2

Not Ready Port(s) = –

Connected Port(s) = 2

Polling Interval = 10000000

Dead Count = 3

Rapid ARP = on

Rapid ARP Interval = 1.0 second(s)

Rapid ARP Count = 10

Failover Policy = PRIORITY_BASED

Fixed Mac Address = off

附：

相關的文件內容如下：

/etc/rc.config.d/netconf:

HOSTNAME=”db1″

OPERATING_SYSTEM=HP-UX

LOOPBACK_ADDRESS=127.0.0.1

ROUTE_DESTINATION[0]=default

ROUTE_MASK[0]=””

ROUTE_GATEWAY[0]=”10.0.25.216″

ROUTE_COUNT[0]=”1″

ROUTE_ARGS[0]=””

ROUTE_SOURCE[0]=””

GATED=0

GATED_ARGS=””

RDPD=0

RARPD=0

DEFAULT_INTERFACE_MODULES=””

INTERFACE_NAME[1]=”lan901″

IP_ADDRESS[1]=”10.0.25.193″

SUBNET_MASK[1]=”255.255.255.192″

BROADCAST_ADDRESS[1]=””

INTERFACE_STATE[1]=”up”

DHCP_ENABLE[1]=”0″

INTERFACE_MODULES[1]=””

INTERFACE_NAME[2]=”lan902″

IP_ADDRESS[2]=”192.168.100.1″

SUBNET_MASK[2]=”255.255.255.0″

BROADCAST_ADDRESS[2]=””

INTERFACE_STATE[2]=”up”

DHCP_ENABLE[2]=”0″

INTERFACE_MODULES[2]=””

/etc/rc.config.d/hp_apaconf:

HP_APA_START_LA_PPA=900

HP_APA_DEFAULT_PORT_MODE=MANUAL

# End of hp_apaconf configuration file

/etc/rc.config.d/hp_apaportconf:

###########################################################################

# The HP_APAPORT_INIT_ARGS are reserved by HP. They are NOT user changable.

HP_APAPORT_INIT_ARGS=”HP_APAPORT_GROUP_CAPABILITY HP_APAPORT_PRIORITY HP_APAPORT_CONFIG_MODE HP_APAPORT_KEY HP_APAPORT_SYSTEM_PRIORITY”

HP_APAPORT_INTERFACE_NAME[0]=lan3

HP_APAPORT_GROUP_CAPABILITY[0]=5

HP_APAPORT_KEY[0]=0

HP_APAPORT_PRIORITY[0]=5

HP_APAPORT_CONFIG_MODE[0]=LAN_MONITOR

HP_APAPORT_SYSTEM_PRIORITY[0]=0

HP_APAPORT_INTERFACE_NAME[1]=lan2

HP_APAPORT_GROUP_CAPABILITY[1]=5

HP_APAPORT_KEY[1]=0

HP_APAPORT_PRIORITY[1]=3

HP_APAPORT_CONFIG_MODE[1]=LAN_MONITOR

HP_APAPORT_SYSTEM_PRIORITY[1]=0

HP_APAPORT_INTERFACE_NAME[2]=lan4

HP_APAPORT_GROUP_CAPABILITY[2]=5

HP_APAPORT_KEY[2]=0

HP_APAPORT_PRIORITY[2]=5

HP_APAPORT_CONFIG_MODE[2]=LAN_MONITOR

HP_APAPORT_SYSTEM_PRIORITY[2]=0

HP_APAPORT_INTERFACE_NAME[3]=lan5

HP_APAPORT_GROUP_CAPABILITY[3]=5

HP_APAPORT_KEY[3]=0

HP_APAPORT_PRIORITY[3]=3

HP_APAPORT_CONFIG_MODE[3]=LAN_MONITOR

HP_APAPORT_SYSTEM_PRIORITY[3]=0

# End of hp_apaportconf configuration file

*優先級：Lan4>lan5, Lan3>Lan2

/etc/lanmon/lanconfig.ascii:

LM_RAPID_ARP on

LM_RAPID_ARP_INTERVAL 1000000

LM_RAPID_ARP_COUNT 10

FAILOVER_GROUP lan901

PRIMARY lan3 5

STANDBY lan2 3

FAILOVER_GROUP lan902

PRIMARY lan4 5

STANDBY lan5 3

zhaohang